Types of Spray Foam
What are the Different types of Spray Foams?
CLOSED-CELL VS. OPEN-CELL FOAM
If your aim is to learn about spray polyurethane foam insulation, you’re on the right page. Before going forward with a spray foam application on either a commercial or residential building, it is important to establish whether you will utilize .05 lb./cu. ft., open-cell foam or 2.0 lb./cu. ft. closed-cell foam. When factoring performance, method of application, and price, the differences between the two are significant.
There are two chief factors to consider when it comes to differentiating open cell and closed-cell foam. First off, it is important to examine each type of foam. With open-cell foam, the minuscule cells of the foam are not entirely closed, so the foam itself is permeable and can fill with air and moisture. These tiny open spaces render the foam weaker and softer feeling than closed-cell foam. Unlike open-cell foam, closed-cell foam has all the tiny cells of the foam sealed. The cells contain a gas that provides the foam with the ability to expand and better insulate a structure. During the formulation process, the cells are designed to have certain attributes.
Open-cell spray polyurethane foam, sometimes called half-pound foam, has a typical density of 0.5 lb. per cubic foot and a typical R-value of 3.5 or 3.6 per inch.
Closed-cell foam, sometimes called two-pound foam, has a typical density of 2 lbs. per cubic foot and an R-value of 6 to 6.5 per inch.
Open-cell spray foam has an average density of 0.5 lbs per cubic foot. It provides a typical R-Value of 3.5 to 3.6 per inch. Since the open cells are relatively vapor-permeable, three inches of open-cell foam have a permeance of 16 perms. In fact, it often requires the use of a vapor retarder when used in interior applications.
Closed-cell foam is itself a vapor retarder. It is vapor semi-impermeable. Two and a half inches of closed-cell foam have a permeance of 0.8 perm.
In What Ways are Open-cell and Closed-Cell Polyurethane Foams Different?
It is important to consider the density of the foam. To determine the density of the foam one solid cubic foot of foam material is weighed. Typically, open-cell foams are in the neighborhood of 0.4 to 0.5 lb./cu. ft. in volume. Closed-cell foam can vary in density when it comes to insulation and roofing applications. For insulation applications, closed-cell foam can fluctuate between 1.7 lb./cu. ft. to 2.0 lb./cu. ft., whereas for roofing applications, contractors will use between 2.8 to 3.0+ lb./cu. ft of foam. The heavier the foam is, the more rigid it can be.
Closed-cell foam has a greater resistance to water vapor and air leakage, it is stronger, and has a higher R-value than open-cell foam. However, because closed-cell foam is higher in density, it requires more material than open-cell foam, therefore, it comes at a higher cost. Despite its higher R-value, closed-cell foam’s cost per R is still more expensive than open-cell foam. To decide which foam to use, it is important to look at characteristics like vapor control, strength, and available space in order to determine the requirements of the application. Open-cell foam usually utilizes water as a blowing agent and it has an R-3.5 value, whereas closed-cell foam requires high R-value blowing agents, yet gives out an R-6 value.
The factors mentioned above are catalysts when deciding which type of foam to use, as closed-cell and open-cell foams are the most common type of polyurethane foams used in building applications. Choosing the correct type of foam is essential, as one type of foam can be unnecessary and sometimes downright ineffective in certain applications. Case in point: Open-cell foam should not be used in applications where water can be absorbed because water is a poor insulator. Thus, using open-cell foam in below-grade or in flotation applications would provide little or no thermal insulation. In roofing applications or situations where the greatest R-value per inch is needed, closed-cell foam would be the correct choice of foam.